• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer

Electrical Engineering News and Products

Electronics Engineering Resources, Articles, Forums, Tear Down Videos and Technical Electronics How-To's

  • Products / Components
    • Analog ICs
    • Connectors
    • Microcontrollers
    • Power Electronics
    • Sensors
    • Test and Measurement
    • Wire / Cable
  • Applications
    • Automotive/Transportation
    • Industrial
    • IoT
    • Medical
    • Telecommunications
    • Wearables
    • Wireless
  • Resources
    • DesignFast
    • Digital Issues
    • Engineering Week
    • Oscilloscope Product Finder
    • Podcasts
    • Webinars / Digital Events
    • White Papers
    • Women in Engineering
  • Videos
    • Teschler’s Teardown Videos
    • EE Videos and Interviews
  • Learning Center
    • EE Classrooms
    • Design Guides
      • WiFi & the IOT Design Guide
      • Microcontrollers Design Guide
      • State of the Art Inductors Design Guide
    • FAQs
    • Ebooks / Tech Tips
  • EE Forums
    • EDABoard.com
    • Electro-Tech-Online.com
  • 5G

Choosing a reference voltage for an ADC

August 30, 2017 By Janet Heath Leave a Comment

Analog-to-digital converters (ADCs) need a reference voltage (VREF) input in order to operate properly. ADCs convert analog inputs that can vary from zero volts on up to a maximum voltage level that is called the reference voltage. The reference voltage determines the ceiling of what the ADC can convert, and is essentially the yardstick against which every proportion and result is measured. Therefore, in choosing a reference voltage (VREF) the voltage output level and initial accuracy are of the first concern.

VREF is also related to the resolution of the ADC. The resolution of an ADC is defined by dividing VREF by the total number of possible conversion values. (Think of the resolution of the ADC as equivalent to the smallest step size of the ADC.)

Attributes like precision, accuracy, and low noise are important for the ADC’s voltage reference, and the type of device used to provide the reference voltage for a data converter matters. The voltage reference is external to the ADC, and along with an amplifier to drive the reference, contributes to the overall system noise.

Figure 1: Both the voltage reference device and the amplifier (reference buffer) can contribute to overall system noise for the ADC. (Source: e2e.ti.com)

 

For microcontrollers (MCUs) that have integrated (internal) ADCs, you may or may not have control over the reference voltage. Some MCUs have an external pin that allows you to provide a voltage reference of your choosing, but others will simply use the MCU’s supply voltage. This can cause inaccuracy, for example, if the MCU accepts 3.3 V analog inputs to the internal ADC while the VREF for that internal ADC is actually the supply voltage to the MCU or 5V. In the end, the power supply, which can reasonably vary by as much as 3%, can cause a fairly significant change to conversion results.

As mentioned in a previous article on ADCs, a 10-bit ADC has 210=1,024 possible steps. The value produced by a 10-bit ADC with a 5V reference and a 3.3V analog input signal (where 3.3V is the highest value measured at the input) would be:

(VIN x 1,024) /VREF = (3.3 V x 1,024)/5 V = 675.84

However, the result, if V REF were 3.3 V, rather than 5 V, would be:

(VIN x 1,024) /VREF = (3.3 V x 1,024)/3.3 V= 1,024

On the other hand, if the power supply or voltage device that is used for VREF varies, the results can differ, even if the same analog input of 1.65 V is received by the ADC:

at VREF = 3.5 V:  (VIN x 1,024) /VREF = (1.65 V x 1,024)/3.5 V= 482.7

 

at VREF = 3.0 V:  (VIN x 1,024) /VREF = (1.65 V x 1,024)/3.0 V= 563.2

 

The variability of the voltage supplied to VREF is a large factor in the accuracy of your ADC. Power supplies or voltage regulator outputs can vary for several reasons that can be based on temperature and load fluctuations, and with variations from supply to supply, among other things.

Figure 2: The reference voltage of an ADC (10-bit is shown) results in output variations.

The VREF for your ADC should be very stable regardless of the temperature it experiences. It should demonstrate excellent performance over temperature. In short, the lower the number of ppm/°C, the better.  Additionally, the initial output voltage accuracy of VREF should be low, in the range of 0.5% or less for precision ADC applications. The voltage reference should have noise value specifications lower than the ADC. The topology of the series voltage reference (as opposed to a shunt voltage reference) favors a better initial voltage performance and low drift over temperature.[i]

As an example, interpreting a datasheet for the TI REF31xx-Q1 series voltage reference shows high accuracy at 0.2% maximum, which means it will not vary more than 0.2% from the nominal value and an excellent specified drift performance over temperature of 20 ppm/°C (maximum) over operating temperatures from –40°C to +125°C. It’s also identified with low output noise at 17 µVpp/V. The other benefit is that the part comes in several voltage options offering VREF at 1.25 V, 2 V, 2.5 V, 3 V, 3.3 V, or 4 V.

Figure 3: A datasheet for a voltage reference. (Source: Texas Instruments.)

The stability of the voltage provided as VREF over varying temperatures is very important. If not, then the ADC will give results that are skewed around the temperature at which it was first calibrated.

VREF should also be a value that is close to the maximum value that the analog input on the ADC will see. For instance, a signal at its highest value (pegged) at 3.3 V into the analog input to the ADC should relate back to a VREF of 3.3 V into the ADC. It is possible to compensate for variations in VREF using software and thereby calibrating the ADC, but this creates another potentially intensive task for the processor.

[i] Baker, B., & Oljaca, M. (2009, 3Q). How the voltage reference affects ADC performance, Part 2. Analog Applications Journal. Retrieved August 20, 2017, from

DesignFast Banner version: 03eceadf

Filed Under: FAQ, Featured, Power Electronic Tips Tagged With: basics, FAQ, texasinstrumentsinc, ti

Reader Interactions

Leave a Reply Cancel reply

You must be logged in to post a comment.

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Primary Sidebar

EE Training Center Classrooms

EE Classrooms

Featured Resources

  • EE World Online Learning Center
  • CUI Devices – CUI Insights Blog
  • EE Classroom: Power Delivery
  • EE Classroom: Building Automation
  • EE Classroom: Aerospace & Defense
  • EE Classroom: Grid Infrastructure
Search Millions of Parts from Thousands of Suppliers.

Search Now!
design fast globle

R&D World Podcasts

R&D 100 Episode 7
See More >

Current Digital Issue

April 2022 Special Edition: Internet of Things Handbook

How to turn off a smart meter the hard way Potential cyber attacks have a lot of people worried thanks to the recent conflict in Ukraine. So it might be appropriate to review what happened when cybersecurity fi rm FireEye’s Mandiant team demonstrated how to infiltrate the network of a North American utility. During this…

Digital Edition Back Issues

Sponsored Content

Positioning in 5G NR – A look at the technology and related test aspects

Radar, NFC, UV Sensors, and Weather Kits are Some of the New RAKwireless Products for IoT

5G Connectors: Enabling the global 5G vision

Control EMI with I-PEX ZenShield™ Connectors

Speed-up time-to-tapeout with the Aprisa digital place-and-route system and Solido Characterization Suite

Siemens Analogue IC Design Simulation Flow

More Sponsored Content >>

RSS Current EDABoard.com discussions

  • Smallest header needed to support PCB vertically above main PCB
  • What base emitter resistors are inside Darlington
  • Simulation of resonator in HFSS
  • series connection of power audio amplifier
  • Sampling with MOS transistor and cap

RSS Current Electro-Tech-Online.com Discussions

  • software PWM
  • ASM - Enhanced 16F and long calls - how?
  • Ampro 16mm Stylist projector woes.
  • Will Header and socket hold this PCB OK?
  • Passthrough charging-simple but impossible to achieve?

Oscilloscopes Product Finder

Footer

EE World Online

EE WORLD ONLINE NETWORK

  • 5G Technology World
  • Analog IC Tips
  • Battery Power Tips
  • Connector Tips
  • DesignFast
  • EDABoard Forums
  • Electro-Tech-Online Forums
  • Engineer's Garage
  • Microcontroller Tips
  • Power Electronic Tips
  • Sensor Tips
  • Test and Measurement Tips
  • Wire & Cable Tips

EE WORLD ONLINE

  • Subscribe to our newsletter
  • Lee's teardown videos
  • Advertise with us
  • Contact us
  • About Us
Follow us on TwitterAdd us on FacebookConnect with us on LinkedIn Follow us on YouTube Add us on Instagram

Copyright © 2022 · WTWH Media LLC and its licensors. All rights reserved.
The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media.

Privacy Policy