(editor’s note: Intrigued by the problem? Have a question or another solution? Then click the “Read more” link and follow the conversation on EDAboard.com or log in to EDAboard and participate in the analog IC forum threads.)
Converting voltage to resistance – My input is a 0-5 V signal. The voltage in this terminals is between this range: 15 to -15 V. The aim is to attenuate it with the resistor. Read more
Modernizing two audio filters – Here are two audio filters for receivers. I would like to test them but I want to make them using NPN transistors instead. Is it enough to replace the PNP transistors with NPN and put a positive VCC where a negative exists now? Also any guess of their operation principles? Read more
Mains isolation with specialty transformer – I desire to measure mains voltage of 230V AC 50Hz as a means of protecting a pump from running at certain low voltages. I have been canvassing for a suitable way I can go about it in a way that I have galvanic isolation of the mains from my control system at a very low cost. I stumbled into this transformer by TDK Corporation: ATB322524-0110 and it is very cheap. I intend to reduce the mains voltage by resistor voltage divider network. Do you think this transformer suitable for the purpose? Do you think I should use some other isolation component instead? Read more
Remove phase lag of voltage transformer – I am working on an energy meter design which uses a 1:1 transformer for voltage measurement and current transformer for current measurement. While experimenting, I found the voltage transformer’s output signal lags by approximately 30 degrees with the input signal. Is there a way to remove this phase lag? Read more
Simple amplifier design – What do you think about this amplifier? Yes, I know the power step, class AB, has no polarization (but with Multisim an error occurs if I place the polarization diodes). Read more
Optocoupler: CTR and REL_CTR – I am studying optocouplers for first-time use. I understand the CTR parameter but not the relative CTR.
1. What is relative CTR and what is it used for?
2. Is there a relationship between CTR and Relative CTR? If there is, what is the relationship?
3. I am designing a simple on/off control system with a process switch as a sensor. I desire a cost-effective optocoupler for the isolation and I chose the Vishay’s TCMT4106. Is this optocoupler appropriate for this requirement? Read more
150V to 5v logic converter – I have a 150V signal coming from a capacitor discharge ignition system that goes into a coil to produce high-voltage that goes toward the spark plug (i.e. CDI). I want to obtain and analyze the timing of the signal from in between the capacitor and the coil and record it on a logic probe. I need some device that will convert the 150V pulse to between 5V-3.3V. the device needs to be fast. Can anyone suggest a device that would be suitable for this application? Read more
Analog output or 4- 20 mA from SCADA – I have an actuator at 240 V that can take an analog output of 4-20 mA signal. I want to change the voltage difference from 2V to 1V. What value in resistance should I change? Read more
Simple, discrete, audio compressor circuit needed – I need discrete components circuit for an audio compressor, or automatic audio level control, or audio limiter for my receiver.
I want to bring the low-level audio signals and the high-level audio signals at the same audio level. I am trying not to attenuate the audio output of it much, so the circuit must have close to unity gain. I have tried the circuit below but it did not have any effect on my receiver; it only attenuated the audio quite a lot. Any ideas? Read more
Need changes in this battery monitor circuit – The battery monitor circuit shown in the diagram works with a voltage difference of 2V. At 27 V, all the LEDs glows. At 25 V, LED 1 gets off . At 23 V LED 2 gets off. Only LED 1 remains off. I want to change the voltage difference from 2V to 1V. What value in resistance should I change? Read more
The post Top analog threads on EDAboard.com – January appeared first on Analog IC Tips.