Cypress Semiconductor Corp. today announced it has embedded compute capabilities into its next-generation memory platform to address the growing demand for trusted intelligence and fail-safe storage in applications such as Advanced Driver Assistance Systems (ADAS) and smart factories. The platform includes standardized intellectual property (IP) that can be reconfigured quickly to address emerging applications. Cypress’ […]
Automotive power switch family handles lighting, body applications
Infineon Technologies AG is launching a new generation of its multichannel SPI high-side power controllers SPOC. The new SPOC series is designed to address interior and exterior lighting applications but also power distribution applications such as door lock and seat heating, as well as lighting and power distribution loads for e-bikes. Similar to the body […]
EMI suppression capacitors rated at 350 Vac
TDK is now offering a new series of EPCOS MKP Y2 capacitors for EMI suppression. In contrast to conventional types that are designed for rated voltages of 300 V AC, these new capacitors offer a permissible rated voltage of 350 V AC. The capacitances of the B3203* series range from 4.7 nF to 1.2 µF. Even under harsh environmental conditions, the […]
High-frequency automotive radar test equipment targets autonomous vehicle efforts
The new, enhanced Keysight E8740A Automotive Radar Signal Analysis and Generation solution enables radar-based, advanced driver assistance systems to proactively detect and mitigate risks of collisions. As advanced driver-assistance systems (ADAS) and autonomous vehicles gain in popularity, they also raise concerns about safety and reliability. Autonomous vehicles are dependent on advanced sensor technology with highly […]
Synchronous secondary buck converters target assisted driving sensor use
ROHM announced the availability of the BD9S series (BD9S400MUF-C, BD9S300MUF-C, BD9S200MUF-C, BD9S100NUX-C, BD9S000NUX-C). This series of automotive synchronous secondary buck DC/DC converters have a high reliability and low power consumption in a compact form factor with a temperature range of -40 to +125 degree. The products are offered in a leadless package with wettable flanks. This makes them […]
Thermal simulation package brings CFD to autonomous electric vehicle design
New Simcenter software for thermal simulation of Autonomous Electric Vehicles (AEVs) is said to be the first such package engineered to address critical, thermal-driven challenges associated with AEV design. “Strategy Analytics expects that the vast majority of self-driving cars will feature electrified powertrains,” said Ian Riches, executive director, Automotive Practice for Strategy Analytics. “The OEMs […]
High-def automotive camera module reference design includes image processor, serializer, power management
OmniVision Technologies, Inc., a leading developer of advanced digital imaging solutions, today announced its high definition (HD) automotive camera module reference design, developed with collaboration from Leopard Imaging and featuring technology from Texas Instruments (TI). The compact design includes OmniVision’s OX01B40 image sensor plus image signal processor (ISP) system-in-package (SiP), as well as TI’s DS90UB933-Q1 or DS90UB935-Q1 serializer chip and TPS65000-Q1 power management integrated circuit (PMIC). All four components are AEC-Q100 Grade […]
Buck-boost controller targets 12-V/12-V redundant battery systems in autonomous vehicles
The Power by Linear LT8708/-1 is a 98% efficient bidirectional buck-boost switching regulator controller that operates between two batteries that have the same voltage, as are used for redundancy in self-driving cars. The LT8708/-1 operates from an input voltage that can be above, below or equal to the output voltage, making it well suited for […]
Injection molding, 3D printing take their places in digital manufacturing
In the context of all the buzz around 3D printing, the term “injection molding” may sound like a ho-hum and low-tech term. However, depending upon your design requirements, there is an important place for both processes and 3D printing (additive manufacturing) is not poised to take over injection molding any time soon. Although 3D printing […]
Key design considerations for sheet metal enclosures
Even the simplest of electronic products need to be enclosed somehow. Additionally, having a basic understanding of how electronics enclosures are fabricated can go a long way to a more successful overall design and positive end-user experience. While there are electronic products that are more suitable for plastic enclosures, sheet metal electronic enclosures have the […]
- 1
- 2
- 3
- …
- 32
- Next Page »
@eeworldonline
EE World Online
@eeworldonline