A new automotive serializer/deserializer (SerDes) receiver (Rx) compliance test solution verifies mobile industry processor interface (MIPI) A-PHY devices based on the Compliance Test Specification (CTS) requirements. This solution was developed in collaboration with BitifEye Digital Test Solutions GMBH and Wilder Technologies, with the support of Valens Semiconductor Ltd.. Silicon vendors are planning to implement MIPI […]
Automotive/Transportation
GaN FETs optimized for 48-V dc/dc power conversion
EPC expands the selection of off-the-shelf GaN FETs in thermally enhanced QFN packages with the introduction of the 100 V EPC2306 designed for 48 V DC-DC conversion used in high-density computing applications, in 48 V BLDC motor drives for e-mobility and robotics, and in solar optimizers and microinverters, and Class D Audio. The EPC2306 GaN […]
GaN half-bridge power ICs enable megahertz-range switching frequencies
Navitas Semiconductor announced the industry’s first GaNSense half-bridge power ICs. These half-bridge ICs enable a new level of MHz switching frequencies while dramatically reducing the system cost and complexity compared to existing discrete solutions. GaNSense half-bridge power ICs integrate two GaN FETs with drive, control, sensing, autonomous protection, and level-shift isolation, to create a fundamental […]
200-V MOSFETs target EV motor control, power supplies
Magnachip Semiconductor Corporation announced that the company has introduced its third-generation 200V Medium Voltage (MV) Metal-Oxide-Semiconductor Field-Effect Transistors (MOSFETs) for Light Electric Vehicles (LEV) motor controllers and industrial power supplies. To maximize energy efficiency in power devices, Magnachip’s new 200V MOSFETs incorporate third-generation trench MOSFET technology. The capacitance was reduced by 50% compared to the previous generation […]
Window-type 40-V voltage detector targets auto, industrial uses
ROHM Semiconductor announced its new high accuracy, ultra-low current consumption voltage detector (reset IC) BD48HW0G-C. The device is optimized for a wide range of automotive and industrial applications requiring voltage monitoring of electronic circuits for increased safety, including automotive electronic control units and factory automation equipment. In recent years, technological innovation in the automotive and industrial […]
High-power fuses optimized for electric vehicle use
Bourns, Inc. announced a new POWrFuse High-Power Fuse model series. Bourns specifically designed the POWrFuse Model PF-K Series to meet ISO 8820-8 standards for the protection of high-voltage accessory circuits in electric vehicles (EVs) and hybrid electric vehicles (HEVs). These circuits are found in a variety of EV/HEV applications including electrical energy storage (ESS), battery disconnect units (BDUs), and […]
Multilayer inductors target automotive PoC apps
TDK Corporation has announced the introduction of the new MLJ1608WG Series of multilayer inductors. These compact components are targeted at use in automotive Power over Coax (PoC) implementations. Mass production began in August 2022. The MLJ1608WG Series inductors achieve a maximum impedance of 2500 Ω. They also retain impedance levels of 1000 Ω over a […]
Microcontroller boosts automotive security
NXP Semiconductors has announced the NCJ37x Secure Element (SE), an automotive-qualified secure microcontroller with advanced cryptographic accelerators and physically built-in electrical attack resistance for various security-critical automotive applications such as smart access key fobs, Qi 1.3 authentication, or car-to-cloud communication. The device supports the protocols from the Car Connectivity Consortium (CCC) and its passive NFC […]
Module adapts IEPE sensors to oscilloscopes
Pico Technology has launched a new solution that allows the use of IEPE sensors on all data acquisition devices with a 1 MΩ BNC interface. The TA487 IEPE Signal Conditioner is a simple adaptor that allows any oscilloscope to capture and measure signals from a large selection of piezo-electric IEPE sensors. Integrated Electronics Piezo-Electric (IEPE) is […]
BNC interface lets piezoelectric sensors hook up to data acquisition gear
A new interface allows the use of IEPE sensors on all data acquisition devices with a 1-MΩ BNC interface. The TA487 IEPE Signal Conditioner is a simple adaptor that allows any PicoScope or oscilloscope to capture and measure signals from a large selection of piezo-electric IEPE sensors, such as the Pico Technology TA095 accelerometer. Integrated […]